Gehl 140
Browse All Gehl or Wheel Loader Models
Contents:
Bucket
| Dump Clearance At Max Raise | 6.46 ft in (1969 mm) |
| Bucket Width | 3.67 ft in (1118 mm) |
Dimensions
| Ground Clearance | 0.63 ft in (191 mm) |
| Length With Bucket On Ground | 11.22 ft in (3419 mm) |
| Width Over Tires | 3.45 ft in (1049 mm) |
| Height To Top Of Cab | 7.19 ft in (2189 mm) |
| Wheelbase | 4.43 ft in (1349 mm) |
| Hinge Pin - Max Height | 8.88 ft in (2705 mm) |
| Reach At Max Lift And Dump | 1.3 ft in (394 mm) |
| Length Of Machine* | 397.6 in (10099.05 mm) |
| Basic Blade Width | 140 in (3556 mm) |
| Note | *Typically equipped with push block and ripper. |
| Maximum Height | 132 in (3352.8 mm) |
| Width | 97.6 in |
Engine
| Number Of Cylinders | 6 |
| Engine Make | 2348 |
| Engine Model | 3TNV76 |
| Net Power | 23.3 hp (17.4 kw) |
| Power Measured @ | 2800 rpm |
| Displacement | 567.5 cu in (9.3 L) |
| Bore | 4.5 in (114.3 mm) |
| Stroke | 5.9 in (149.9 mm) |
| Emissions | U.S. EPA Tier 4 Final/EU Stage IV |
| Engine Model | Cat C9.3 |
| Net Power - Eec 80/1269 | 250 hp (186.5 kw) |
| Maximum Torque | 827 lb ft (1121.3 Nm) |
| Net Power - Iso 9249/Sae J1349 | 250 hp (186.5 kw) |
| Base Power (1st Gear) - Net | 177 hp (132 kw) |
| Standard Capability | 109 degrees |
| Torque Rise - Iso 9294 | 40% |
Operational
| Operating Weight | 3911.1 lb (1774 kg) |
| Fuel Capacity | 6.9 gal (26 L) |
| Hydraulic System Fluid Capacity | 9 gal (34 L) |
| Static Tipping Weight | 1929.1 lb (875 kg) |
| Turning Radius | 6.9 ft in (2101 mm) |
| Operating Voltage | 12 V |
| Tire Size | 27x10.5-15 |
Transmission
| Max Speed - Forward | 10.5 mph (16.9 km/h) |
| Max Speed - Reverse | 10.5 mph (16.9 km/h) |
Hydraulic System
| Relief Valve Setting | 4640 psi (31991.7 kPa) |
| Pump Flow Capacity | 20.9 gal/min (79 L/min) |
Moldboard
| Cutting Edge | 6 in (152.4 mm) |
| Blade Width | 12 ft in (3.7 m) |
| Arc Radius | 16.3 in (414.1 mm) |
| Throat Clearance | 6.5 in (165.1 mm) |
| End Bit | 6 in |
Service Refill
| Fuel Tank | 100 gal (378.6 L) |
| Hydraulic System | 14.5 gal (54.9 L) |
| Cooling System | 15 gal (56.8 L) |
| Def Tank | 3.3 gal (12.5 L) |
| Circle Drive | 1.8 gal (6.9 L) |
| Engine Crankcase | 7.9 gal (30 L) |
| Front Wheel Spindle Bearing - Each | 0.2 gal (0.5 L) |
Machine Weight
| Note | *Typically equipped with push block and ripper. |
| Weight* | 42.4 lb (19.2 kg) |
| All-Wheel Drive (Awd) Weight | 44.7 lb (20.3 kg) |
Blade Range
| Circle Centershift - Right | 28.6 in (726.5 mm) |
| Circle Centershift - Left | 29.6 in (751.9 mm) |
| Moldboard Sideshift - Right | 20.1 in (510.6 mm) |
| Moldboard Sideshift - Left | 26.1 in (663 mm) |
| Blade Tip Range - Forward | 40 degrees |
| Blade Tip Range - Backward | 5 degrees |
| Maximum Shoulder Reach Outside Of Tires - Right | 75.9 in (1927.9 mm) |
| Maximum Shoulder Reach Outside Of Tires - Left | 69.4 in (1762.8 mm) |
| Maximum Lift Above Ground | 18.9 in (480.1 mm) |
| Maximum Depth Of Cut | 28.9 in (734.1 mm) |
