Caterpillar 16H
Browse All Caterpillar or Motor Grader Models
Contents:
Dimensions
| Overall Length | 32.79 ft in (9994 mm) |
| Width Over Tires | 10.08 ft in (3077 mm) |
| Wheelbase | 22.83 ft in (6960 mm) |
| Rear Ground Clearance | 1.34 ft in (409 mm) |
| Tandem Axle Wheelbase | 6 ft in (1841 mm) |
| Front Ground Clearance | 2.4 ft in (732 mm) |
| Blade Base | 10.08 ft in (3071 mm) |
| Height To Top Of Isomount Cab | 11.58 ft in (3524 mm) |
Engine
| Number Of Cylinders | 6 |
| Net Power Gear 4-6 | 285 hp (212.6 kw) |
| Engine Make | 2236 |
| Engine Model | 3196 ETA |
| Net Power Gear 1-2 | 265 hp (198 kw) |
| Power Measured @ | 2000 rpm |
| Net Power Gear 5-6 | 285 hp (212.6 kw) |
| Max Power | 285 hp (212.6 kw) |
| Net Power Gears 7-8 | 285 hp (212.6 kw) |
| Net Torque Gears 7-8 | 1143 lb ft (1550 Nm) |
| Displacement | 726 cu in (11.9 L) |
Operational
| Std Operation Weight - Front Axle | 15397 lb (6982 kg) |
| Std Operation Weight - Rear Axle | 39153 lb (17758 kg) |
| Hydraulic System Fluid Capacity | 34 gal (129 L) |
| Std Operation Weight - Total | 54550 lb (24740 kg) |
| Max Operation Weight - Front Axle | 19502 lb (8846 kg) |
| Max Operation Weight - Rear Axle | 50146 lb (22746 kg) |
| Max Operation Weight - Total | 69648 lb (31592 kg) |
| Fuel Capacity | 130 gal (492 L) |
| Cooling System Fluid Capacity | 12.3 gal (46.5 L) |
| Rear Diff/Final Drive Fluid Capacity | 30.1 gal (114 L) |
| Circle Gearbox Fluid Capacity | 2.1 gal (8 L) |
| Tandem Case Fluid Capacity (Each) | 31.5 gal (121 L) |
| Operating Voltage | 24 V |
| Alternator Supplied Amperage | 75 amps |
Steering
| Articulation Angle | 20 degrees |
| Turning Radius | 27 ft in (8.2 m) |
Transmission
| Transmission Type | direct drive, power shift, planetary |
| Number Of Gears - Forward | 8 |
| Number Of Gears - Reverse | 8 |
| Max Speed - Forward | 29.9 mph (48.1 km/h) |
| Max Speed - Reverse | 28.4 mph (45.7 km/h) |
Front Axle
| Wheel Lean | 18 degrees |
| Oscillation - Total | 32 degrees |
| Ground Clearance | 2.4 ft in (732 mm) |
Moldboard
| Moldboard Width | 16 ft in (4877 mm) |
| Moldboard Height | 31 in (787 mm) |
| Moldboard Thickness | 1 in (25 mm) |
| Max Depth Of Cut | 18.5 in (470 mm) |
| Side Shift Left | 25.6 in (650 mm) |
| Side Shift Right | 31.1 in (790 mm) |
| Blade Pull At Max Weight | 45131 lb (20471 kg) |
| Blade Down Pressure | 34901.4 lb (15831 kg) |
Hydraulic System
| Pump Type | axial piston |
| Pump Flow | 66 gal/min (254 L/min) |
| Relief Valve Pressure | 3500 psi (24150 kPa) |
Circle
| Diameter | 71.8 in (1822 mm) |
| Shift Left | 27.2 in (690 mm) |
| Shift Right | 22 in (560 mm) |
| Max Reach Outside Tires - Left | 91 in (2311 mm) |
| Max Reach Outside Tires - Right | 91 in (2311 mm) |
| Max Lift Above Ground | 16.5 in (419 mm) |
| Blade Tip Angle - Front | 40 degrees |
| Blade Tip Angle - Rear | 5 degrees |
